凝胶型99Mo-99mTc发生器研究现状

与裂变型⁹⁹Mo-^99mTc发生器相比，凝胶型⁹⁹Mo-^99mTc发生器制备^99mTc具有工艺简单、产生的放射性废物容易处理、对环境影响小等优点。本文主要论述了凝胶型⁹⁹Mo-^99mTc发生器与裂变型⁹⁹Mo-99mTc发生器的区别，堆照生产⁹⁹Mo原料和凝胶材料的研究进展，凝胶结构以及凝胶组分等多种条件因素对凝胶型⁹⁹Mo-^99mTc发生器性能的影响等，并对低比活度⁹⁹Mo生产^99mTc的研究进展进行综述。     

Closed-Form Analysis of Various Diversity Techniques for Multiband OFDM UWB System Over Log-Normal Fading Channels

Wireless Personal Communications - In this paper, we investigate the effect of multipath fading on the combined signal-to-noise ratio (SNR) in conjunction with multiband orthogonal frequency...     

SNCR脱硝技术在液态排渣煤粉工业锅炉中的应用

为了检验选择性非催化还原（SNCR）脱硝技术在高效低NO_x液态排渣煤粉工业锅炉中的应用效果，本文在一台8.4MW有机热载体锅炉炉膛内开展了SNCR脱硝技术工业化试验研究。选用尿素作为还原剂，搭建了工业化SNCR脱硝试验平台。在10%、15%、20%三种浓度尿素溶液下进行了不同尿素溶液喷射量、不同氧含量、不同锅炉负荷下的SNCR脱硝试验研究。试验结果表明，提出的“低NO_x燃烧+SNCR脱硝”耦合技术方案是可行的，SNCR脱硝效率在80%以上，完全能够达到烟气中NO_x低于50mg/m³的超低排放要求。     

超临界二氧化碳干气密封稳态性能研究

以超临界二氧化碳(S-CO_2)干气密封为研究对象,建立变黏度变密度雷诺方程,通过构建物性数据库的方式对黏度及密度进行处理,并采用有限差分法对控制方程进行求解,得到端面压力分布,并计算开启力、泄漏量、摩擦扭矩和气膜刚度等稳态性能参数。结果表明:随着压力、转速的增大,开启力、泄漏量、摩擦扭矩、气膜刚度等参数均增大;随着槽坝比和槽深的增加,开启力、泄漏量和气膜刚度均增大,摩擦扭矩减小;随着槽数的增加,各稳态性能参数均减小;将槽坝比控制在0.5～1的范围内,有助于提高密封稳定性。     

刚性地面对爆炸冲击波传播规律的影响

为研究刚性地面对爆炸冲击波传播特性的影响,采用ANSYS/LS-DYNA对TNT炸药在刚性地面工况下起爆后的整个过程进行了数值分析,得到了刚性地面工况下爆炸冲击波的传播规律以及特征参数,并将其与自由空气工况下爆炸冲击波的传播规律以及特征参数进行了对比分析。建立了TNT炸药在刚性地面工况下起爆后,比例距离在0.5 m/kg^1/3≤Z≤3 m/kg^1/3之间时的冲击波超压峰值简便计算公式,分析了起爆高度对刚性地面附近冲击波的影响规律,并得到了刚性地面反射增强效应作用范围的判别公式。数值分析所得结果可为结构或构件在刚性地面上发生爆炸时荷载的初步确定提供一定的参考。     

毫米波波束管理的设计与研究

毫米波是第五代移动通信系统的重要通信技术,因其频谱特性可以利用大带宽承载大量信息,有效提升系统的吞吐量。高频段毫米波传输具有高损耗性,且受环境影响较大,为了支持非视距和移动性,必须支持准确且实时的波束跟踪以确保信号传输质量。波束管理的目的是使得基站与终端之间发送与接收波束对准以提高链路的性能。文中根据3GPP协议规范设计了波束管理方案,包括以下几方面的内容:波束扫描、波束测量、波束上报、波束指示、波束失败恢复。     

Review on nano-and microfiller-based polyamide 6 hybrid composite: Effect on mechanical properties and morphology

Polyamide 6 (PA6)-based composites are of evolving interest due to its high strength, wear resistance, and barrier properties. The use of binary composites mostly with nanomaterial and glass fibers has been reviewed and presented in literature. However to obtain a balance of properties like stiffness, toughness, and strength along with cost reduction, ternary composites of PA6 have been designed. To achieve the balance, PA6 blend-based composites, with combination of microfiller/nanofiller or PA6 with combination micro-microfiller, PA6 with microfiller/nanofiller and fiber have been designed. The properties of PA6-based ternary hybrid composites depend on type of dispersed phase used, presence of compatibilizer, type of filler used (nanofiller or microfiller or fiber or hybrid) and combination of fillers used. However, a review in this direction is not available in literature. Here, in this study, an overall understanding of various fillers, dispersed phase, and their combinations can be understood along with the discussion on effect of these on tensile properties and morphology of hybrid composite. In this study, an attempt has been made to review the various fillers and dispersed phase and their combinations which have been used in designing the PA6 hybrid composite with good balance of stiffness, toughness, and strength.     

极薄、超宽规格装甲板压力淬火工艺数值模拟优化

利用数值模拟的方法对极薄、超宽规格装甲板淬火过程的畸变进行了模拟研究,并对脉冲式压力淬火的控制参数进行了优化。通过对比不同冷却条件装甲板的变形量,确定了脉冲式压力淬火的脉冲压力和周期。结果表明,脉冲约束的模拟条件下,装甲板在厚度Z方向上的最终变形量为1.7 mm,不仅小于2 mm的标准要求,而且可以实现装甲板的小淬火畸变前提下满足其表面无压痕、划痕等其他损伤的实际生产需求。     

Heavy Water Additive in Formamidinium: A Novel Approach to Enhance Perovskite Solar Cell Efficiency

Heavy water or deuterium oxide (D₂O) comprises deuterium, a hydrogen isotope twice the mass of hydrogen. Contrary to the disadvantages of deuterated perovskites, such as shorter recombination lifetimes and lower/invariant efficiencies, the serendipitous effect of D₂O as a beneficial solvent additive for enhancing the power conversion efficiency (PCE) of triple-A cation (cesium (Cs)/methylammonium (MA)/formaminidium (FA)) perovskite solar cells from ≈19.2% (reference) to 20.8% (using 1 vol% D₂O) with higher stability is reported. Ultrafast optical spectroscopy confirms passivation of trap states, increased carrier recombination lifetimes, and enhanced charge carrier diffusion lengths in the deuterated samples. Fourier transform infrared spectroscopy and solid-state NMR spectroscopy validate the N–H₂ group as the preferential isotope exchange site. Furthermore, the NMR results reveal the induced alteration of the FA to MA ratio due to deuteration causes a widespread alteration to several dynamic processes that influence the photophysical properties. First-principles density functional theory calculations reveal a decrease in PbI₆ phonon frequencies in the deuterated perovskite lattice. This stabilizes the PbI₆ structures and weakens the electron–LO phonon (Fröhlich) coupling, yielding higher electron mobility. Importantly, these findings demonstrate that selective isotope exchange potentially opens new opportunities for tuning perovskite optoelectronic properties.